Product Catalog

The AGH001 is a 6 sensor Optical Array Gas Hold Up tool. Both gas hold up and bubble count are provided by each sensor.

The RAS Calibration and Verification Tank allows for periodic verification of correct tool operation and allows the tool to be tested at surface in a safe fashion. The tank is fabricated from steel and filled with water. The water provides excellent shielding and a known point for the tool verification.

The Capacitance Flow & Temperature Tool offers a reduced length multiple sensor solution. All 1-3/8” Fixed Cage Spinners and our 1-3/8” Full Bore Spinner are compatible with the CFT101.

The Capacitance Flow & Temperature Tool offers a reduced length multiple sensor solution. All 1-3/8” Fixed Cage Spinners and our 1-3/8” Full Bore Spinner are compatible with the CFT104.

The Compensated Neutron Tool (CNT) uses dual, high-temperature, ruggedized He3 thermal neutron detectors to measure formation porosity through casing and cement.

The HXO005 is required when using both Hunter tools and 3^rd party tools in passenger mode. The HXO005 provides tool bus termination for the Hunter tool bus and the electrical connection for the passenger tools.

The HXO009 and HXO010 crossovers are used to allow the RAS002 to run upside down (inverted) as this may be required in some circumstances.

The DAI001 utilizes two orthogonally placed dual-axis accelerometers to detect linear acceleration in three perpendicular directions. This enables both tool deviation and rotation to be determined.

The DLC002 Dummy Logging Cable/Line Simulator allows logging tools to be tested on three different simulated line lengths with 90Ω, 160Ω and 220Ω representing Short, Medium and Long mono conductor cable lengths.

The Fast Response Temperature tool measures well bore temperature by means of a platinum resistance thermometer housed in a low mass Inconel tube providing a fast response and an accurate measurement.

The FCS Mechanical section is run in combination with the 1-11/16” FLTE (Flow & Temperature Electronics) which combines the flowmeter sensor electronics with a fast response temperature tool or with our 1-11/16” CFT (combined Capacitance, Flow & Temperature) tool.

The FCS Mechanical section is run in combination with the 1-3/8” FLTE (Flow & Temperature Electronics) which combines the flowmeter sensor electronics with a fast response temperature tool or with our 1-3/8” CFT combined Capacitance, Flow & Temperature tools.

The Flow Through Sampler (FTS) is a device for obtaining fluid samples from a producing well. It is an entirely rugged, field proven mechanical device controlled via pre-selected timer clocks.

The FLTE is used in with both the FBSM01 (Full Bore Spinner) and the FCSM (Fixed Cage Spinner Mechanical) range of products. A dedicated hall effect array provides 10 pulses per revolution flowmeter output and a fast response PRT measures well bore temperature.

The FLTE is used in with both the FBSM101 (Full Bore Spinner) and the FCSM (Fixed Cage Spinner Mechanical) range of products. A dedicated hall effect array provides 10 pulses per revolution flowmeter output and a fast response PRT measures well bore temperature.

The Fluid Capacitance Tool provides an indication of the fluid type surrounding the sensor by measuring the dielectric constant of the fluid between the sensor and tool body. Used in combination with other sensors it provides qualitative fluid identification data.

The FDT utilizes a double encapsulated low energy AM241 source and scintillation detector assembly to measure fluid density in the measurement window of the tool.

The FDT utilizes a double encapsulated low energy AM241 source and scintillation detector assembly to measure fluid density in the measurement window of the tool.

The FBS Mechanical is connected to the 1-11/16” FLTE (Flow & Temperature Electronics) which combines the flowmeter sensor electronics with a fast response temperature tool or with our 1-11/16” CFT (combined Capacitance, Flow & Temperature) tool.

The FBS Mechanical is connected to the 1-3/8” FLTE (Flow & Temperature Electronics) which combines the flowmeter sensor electronics with a fast response temperature tool or with our 1-3/8”CFT (combined Capacitance, Flow & Temperature) tool.

The Flowmeter closes while passing through the completion tubing and other restrictions and opens in the casing or liner allowing the use of optimum diameter impellers that occupy a large cross-sectional area. This, and the use of low friction bearings, keeps the flowmeter threshold very low.

This Gamma Ray – Casing Collar Locator (CCL) tool utilizes a scintillation style detector with a 1 x 4 inch crystal coupled to a ruggedized high temperature photomultiplier tube packaged in a shock mounted assembly.

This Gamma Ray – Casing Collar Locator (CCL) tool utilizes a scintillation style detector with a 1 x 4 inch crystal coupled to a ruggedized high temperature photomultiplier tube packaged in a shock mounted assembly.

The Gamma Ray – CCL – Neutron Tool utilizes a scintillation style detector using a 1-inch diameter x 4-inch long crystal for the gamma ray measurement.

The GCL is a combined Gamma Ray & Casing Collar Locator tool which provides a passive measurement of gamma radiation by means of a Sodium Iodide Scintillation Detector and identifies of changes metal thickness by means of a collar locator.

The GCL is a combined Gamma Ray & Casing Collar Locator tool which provides a passive measurement of gamma radiation by means of a Sodium Iodide Scintillation Detector and identifies of changes metal thickness by means of a collar locator.

The GCL is a combined Gamma Ray & Casing Collar Locator tool which provides a passive measurement of gamma radiation by means of a Sodium Iodide Scintillation Detector and identifies of changes metal thickness by means of a collar locator.

This Gamma Ray Tool is run below the Cement Bond Tool (CBT). The Gamma Ray can be stacked with a Casing Collar Locator (CCL), Neutron or Compensated Neutron Tool below the CBT or run alone.

The HXO014 is intended to be used with the Telemetry Control Unit (TCU) as a expendable piece to prevent galling and/or damage at the upper connection of the TCU pressure housing.

The HAC001 provides a constant force across its opening range and therefore excellent centralization in vertical, deviated or horizontal wells. Operating effectively in tubing or casing up to 9-5/8” the HAC has been designed to place the rollers precisely where they need to be.

The HAC009 provides effective centralisation for down hole tools with 15/16-10 UN-2A Threads (15/16 Sucker Rod Connections).

The HAC003 provides constant force across its opening range and therefore excellent centralization in vertical, deviated or horizontal wells. Operating effectively in casing up to 13-3/8” the HAC has been designed to place the rollers precisely where they need to be.

The HAC005 provides a constant force across its opening range and therefore excellent centralization in vertical, deviated or horizontal wells. Operating effectively in tubing or casing up to 6.6” the HAC has been designed to place the rollers precisely where they need to be.

The HAC001-HT provides a constant force across its opening range and therefore excellent centralization in vertical, deviated or horizontal wells. Operating effectively in tubing or casing up to 9-5/8” the HAC has been designed to place the rollers precisely where they need to be.

The IFM is a compact inline tool that provides a continuous flowmeter log while in tubing and can provide a secondary/back up flowmeter to the Full Bore or Fixed Cage Spinners whilst logging in casing or liners.

The IFM is a compact inline tool that provides a continuous flowmeter log while in tubing and can provide a secondary/back up flowmeter to the Full Bore or Fixed Cage Spinners whilst logging in casing or liners.

The IFM is a compact inline tool that provides a continuous flowmeter log while in tubing and can provide a secondary/back up flowmeter to the Full Bore or Fixed Cage Spinners whilst logging in casing or liners.

IntelleX™ DYNAWELL Low Power Electronic Triggers are battery powered low power electronic firing heads used to initiate the detonation of ballistic devices with the highest degree of safety and control.

IntelleX™ EBW Low Power Electronic Triggers are battery powered low power electronic firing heads used to initiate the detonation of ballistic devices with the highest degree of safety and control.

IntelleX™ Low Power Electronic Triggers are battery powered low power electronic firing heads used to initiate the detonation of ballistic devices with the highest degree of safety and control. These triggers are availble with JRC RED^® (Rig Environment Detonator) or Owen Green Det™ Electronic Detonators.

The Hunter Interface Panel (HIP002) is a USB device that adds support for Hunter tools to the Scientific Data Systems STIP.

Contains all hand tools required for standard 1 11/16” OD tools.

The KJT is used where there is a need to reduce the overall rigid length of a tools string, to provide an offset or in pairs to decouple the toolstring from coiled tubing or a well tractor.

The KJT is used where there is a need to reduce the overall rigid length of a tools string, to provide an offset or in pairs to decouple the tool string from coiled tubing or a well tractor.

The KJT is used where there is a need to reduce the overall rigid length of a tools string, to provide an offset or in pairs to decouple the tool string from coiled tubing or a well tractor.

The KPerm™ Dual Pressure /Temperature /Vibration (DPTV) gauge measures 2 pressures, 2 temperatures and 2 vibration as per the details on the tables below. All six transducers are contained in one gauge housing that is internally and externally E-beam welded and designed for maximum shock and vibration resistance to enhance reliability and performance.

The KPerm™ Quartz Permanent Downhole Gauge is a permanently installed inside the Probe’s solid gauge mandrel.

Probe Multi-Drop Gauges are based on our field proven permanent piezo gauge technology. Up to 6 gauges can be run on a single TEC cable conductor.

Surface Data Acquisition Cards are designed to supply power to and communicate with the downhole gauge; a single card can interface with up to 4 permanent downhole gauges.

The permanent gauge Surface Read Out (SRO) panel provides the interface to the downhole gauge and enables it to communicate to surface.

The Hunter Logging Panel (HLP001) is a complete logging panel providing full support for our standard service telemetry.

The HLP001 – combined Logging Panel with Tool Power Supply and Depth/Tension Inputs. This is a slim “1U” panel that supports all Hunter Well Science products.

The MBS001/002 is used in conjunction with the Memory Logging Tool (MLT001) and houses the battery pack.

The MBS003/004 is used in conjunction with the Memory Logging Tool (MLT002) and houses the battery pack.

The MBS006 is designed specifically for Memory RAS logging applications.

The MBS101 is used in conjunction with the Memory Logging Tool (MLT101) and houses the battery pack.

The MBS103 is used in conjunction with the Memory Logging Tool (MLT102) and houses the battery pack.

The MLT enables use of all Hunter logging tools without the use of an electric line cable. Tool string power is derived from a suitable battery pack housed in a MBS (Memory Battery Sub).

The MLT enables use of all Hunter logging tools without the use of an electric line cable. Tool string power is derived from a suitable battery pack housed in a MBS (Memory Battery Sub).

The PTSCCL1 is a combined pressure, temperature, flow and casing collar locator tool in a compact 1 3/8” outside diameter size.

The QPT utilizes an industry standard Quartzdyne® Pressure Transducer to provide well bore pressure and gauge temperature. This precision quartz pressure transducer provides a continuous measurement of well pressure during dynamic passes or during pressure build ups or draw downs.

The QPT utilizes an industry standard Quartzdyne® Pressure Transducer to provide well bore pressure and gauge temperature. This precision quartz pressure transducer provides a continuous measurement of well pressure during dynamic passes or during pressure build ups or draw downs.

The Reservoir Analysis Sonde, is a multi-detector pulsed-neutron system for measuring reservoir saturation using Sigma and Carbon-Oxygen techniques.

The RAS Sigma Tool (RAS-Σ), is a multi-detector pulsed-neutron system for measuring reservoir saturation using Sigma techniques.

The BAT_RAS is a 14 x CC Cell Battery Pack for Reservoir Analysis Sonde memory logging operations.

The RSS is a mandatory component in a Memory-RAS string. Positioned between the battery and MLT, it is equipped with pressure and temperature sensors to monitor borehole conditions against user programmable thresholds. A power switch is included in the RSS to disable battery power to MLT (and all attached tools) in case of tool failure.

The Roller Deployment Tool is a short inline device that helps reduce toolstring friction and ease well entry in deviated holes.

The Spectral Gamma Ray & CCL Tool operates on our common tool bus and can be combined with the Reservoir Analysis Sonde, Production Logging Tools or both.

The Spectral Gamma Ray & CCL Tool operates on our common tool bus and can be combined with the Reservoir Analysis Sonde, Production Logging Tools or both.

The Scientific Data Systems STIP provides support for a very wide range of products. When fitted with either our HSM002 (Hunter Surface Modem) or used with our HIP002 (Hunter Interface Panel) it provides full support for all standard Hunter Well Science products.

The HSM002 is installed into the HIP002, HLP001 or SDS STIP Panels and adds full telemetry support for all Hunter standard products on standard service electric wireline lengths of up to 9,100m (30,000ft).

The SJT001 is a pressure compensated mono-conductor swivel that allows rotation between the upper and lower tools joints while maintaining electrical continuity.

The TCU is the communications control centre for the logging system. It provides reliable bi-directional communications on standard service mono-conductor electric wirelines of up to 9,100m (30,000ft). The tool controls the collection of data from the tools below and packages it for transmission to the surface system.

The TCU is the communications control centre for the logging system. It provides reliable communications on standard service mono-conductor electric wirelines of up to 9,100m (30,000ft).

The TGC003 is a 2 3/4” Gamma Ray & Casing Collar Locator tool which provides a passive measurement of gamma radiation using a Sodium Iodide Scintillation Detector and identifies changes in metal thickness by using a collar locator. It is also the communications control centre for the logging system.

The TCT provides continuous downhole tension and compression measurement during logging. This measurement is useful in preventing damage to wireline cable or logging tool string.

The TBN001 is required when the CFT or FLTE tools are not run. Under normal circumstances these tools would provide line termination and a pressure seal. If they are not used the TBN001 is required.

The TBN002 serves the same function as the TBN001 but includes a 15/16” Box connection that’s allows for other tools or items to be run below the string, memory tools or swab cups for example.

The TBN101 is required when the CFT or FLTE tools are not run. Under normal circumstances these tools would provide line termination and a pressure seal. If they are not used the TBN001 is required.

The TBN102 serves the same function as the TBN001 but includes a 15/16” Box connection that’s allows for other tools or items to be run below the string, memory tools or swab cups for example.

The TIB001 is a USB device that replaces the Surface Modem and TCU or Memory Tool for tool testing purposes.

The XY Caliper tool provides a continual measurement of independent X & Y internal diameters by means of measurement arms set at 90° apart.